Product Detail
Clear anti slip tape is ideal for use on decorative surfaces as the finish is nearly transparent similar to looking through frosted glass. It is made from silica particles bonded to clear PVC for a near-transparent slip-resistant surface.
Features and Benefits of Clear Anti Slip Safety Tape:
- Used mainly for decorative surfaces such as tiles or terrazzo, painted or varnished surfaces
- Available in 3 sizes: 2" x 60 ft., 3" x 60 ft., and 4" x 60 ft.
- Use the Safety Tape Primer on dusty concrete, porous, or other weak surfaces to ensure better adhesion
- To protect against wearing and water seepage, use Safety Tape Edge Sealer.
Samples available upon request.
Specifications
| Appearance: | Clear, near transparent anti-slip surface, keeps the decorative appearance of the original surface, self-adhesive backing |
| Primer Required: | Yes for dusty, porous or gritty surfaces |
| Usage Interior/Exterior: | Interior |
| Suitable for: | Decorative surfaces such as tiles, terrazzo, painted or varnished surfaces on floors, ramps and steps |
| Curing Time (Hours): | Full cure in 48 hours |
How to Apply
Surface preparation: Wash the area to remove any grease, oil, dirt, or other contaminates, rinse and allow to dry. The Safety Tape can be applied to any smooth surface such as concrete, wood, metal, tile, terrazzo, and painted or varnished surfaces. Use the Safety Tape Primer on dusty concrete, porous, or other weak surfaces to ensure better adhesion.
Application: Apply only when air and surface temperature are above 50°F (10°C). The surface area must be clean and dry at the time of application. On stair trends and landings, apply the Safety Tape at least 3/8 back from the edge to avoid edge curl. When applying a strip of Safety Tape, do not peel off entire backing all at once. Rather, peel back about 2 from the end of the strip to expose the adhesive and position in place. Press down firmly, then remove the remainder of backing from the Safety Tape while affixing it to the surface. Avoid stretching the tape when placing it into position. The Safety Tape may be peeled back up to reposition it if necessary, but try to avoid repeating this action. Once in place, firmly press down on the Safety Tape by hand or with your foot to secure it. The Safety Tape is suitable to support light foot traffic immediately, however it requires 24 hours for the adhesive to achieve full cure.
Clear anti slip tape is ideal for use on decorative surfaces as the finish is nearly transparent similar to looking through frosted glass. It is made from silica particles bonded to clear PVC for a near-transparent slip-resistant surface.
Features and Benefits of Clear Anti Slip Safety Tape:
- Used mainly for decorative surfaces such as tiles or terrazzo, painted or varnished surfaces
- Available in 3 sizes: 2" x 60 ft., 3" x 60 ft., and 4" x 60 ft.
- Use the Safety Tape Primer on dusty concrete, porous, or other weak surfaces to ensure better adhesion
- To protect against wearing and water seepage, use Safety Tape Edge Sealer.
Samples available upon request.
| Appearance: | Clear, near transparent anti-slip surface, keeps the decorative appearance of the original surface, self-adhesive backing |
| Primer Required: | Yes for dusty, porous or gritty surfaces |
| Usage Interior/Exterior: | Interior |
| Suitable for: | Decorative surfaces such as tiles, terrazzo, painted or varnished surfaces on floors, ramps and steps |
| Curing Time (Hours): | Full cure in 48 hours |
Surface preparation: Wash the area to remove any grease, oil, dirt, or other contaminates, rinse and allow to dry. The Safety Tape can be applied to any smooth surface such as concrete, wood, metal, tile, terrazzo, and painted or varnished surfaces. Use the Safety Tape Primer on dusty concrete, porous, or other weak surfaces to ensure better adhesion.
Application: Apply only when air and surface temperature are above 50°F (10°C). The surface area must be clean and dry at the time of application. On stair trends and landings, apply the Safety Tape at least 3/8 back from the edge to avoid edge curl. When applying a strip of Safety Tape, do not peel off entire backing all at once. Rather, peel back about 2 from the end of the strip to expose the adhesive and position in place. Press down firmly, then remove the remainder of backing from the Safety Tape while affixing it to the surface. Avoid stretching the tape when placing it into position. The Safety Tape may be peeled back up to reposition it if necessary, but try to avoid repeating this action. Once in place, firmly press down on the Safety Tape by hand or with your foot to secure it. The Safety Tape is suitable to support light foot traffic immediately, however it requires 24 hours for the adhesive to achieve full cure.
