Product Detail
Epoxicote High Build is our popular range of heavy-duty floor paint. It delivers an ultra-hard wearing chemical resistant, gloss floor coating. This one coat, high build coating offers superior protection for you concrete floors.
- Gloss finish
- 100% solids epoxy resin formula
- High-build application gives excellent wear resistance
- Protects the concrete from oil and chemical contamination
- Non-tainting and virtually solvent-free
- Easy to clean surface
- Coverage is approx. 190 sq ft per 1.05 gallon kit
We recommend Epoxicote High Build Rapid for jobs that need less down time, Epoxicote High Build Cold Cure for cold environment applications, and Epoxicote High Build Anti-Slip for areas that need added safety from slip hazards.
Specifications
| Usage Interior/Exterior: | Interior |
| Finish: | Glossy, smooth |
| Suitable for: | Concrete, well bonded paint, wood, some metals |
| Primer Required: | Yes, on bare concrete and very porous surfaces should be primed with 4 Hour Epoxy Primer |
| Recommended Number of Coats: | One is usually sufficient |
| Pot Life: | 25 minutes at 70°F |
| Curing Time (Hours): | At 70°F 12-16 hour for light foot traffic, 24 for normal traffic, 36 to 48 hours for vehicle traffic |
How to Apply
Preparation: Concrete and Brick
Concrete to be treated must be dry, at least four weeks old and free of any soft surface laitance, or contamination All loose material should be removed. Very smooth bare concrete or concrete with soft surface laitance should be etched with Watco Cemtetch and the area thoroughly hosed off and allowed to dry. Grease or oil should be removed with Watco Bio-D (or similar degreaser) and the area thoroughly hosed off and allowed to dry. Very smooth previously painted surface should preferably be abraded to improve adhesion.
Preparation: Steel
Remove loose or flaking material, rust and any previous coatings by wire brushing or disc grinding to achieve a bright surface. Grease or oil should be removed with Watco Bio-D and the metal then washed with water and allowed to dry. Coating should be carried out immediately providing flash rusting has not occurred.
Mixing
Each Epoxicote High Build kit consists of a container of curing agent and a container of resin. The curing agent and resin must be thoroughly mixed together with a paint mixer attached to an electric drill for 2 to 3 minutes until an even color is obtained. Do not mix more than one unit at a time.
Application
Epoxicote High Build: Best results are obtained in warm conditions (minimum 60°F). On horizontal surfaces apply by medium pile type roller (not foam) in one coat.
Data Sheet
Epoxicote High Build is our popular range of heavy-duty floor paint. It delivers an ultra-hard wearing chemical resistant, gloss floor coating. This one coat, high build coating offers superior protection for you concrete floors.
- Gloss finish
- 100% solids epoxy resin formula
- High-build application gives excellent wear resistance
- Protects the concrete from oil and chemical contamination
- Non-tainting and virtually solvent-free
- Easy to clean surface
- Coverage is approx. 190 sq ft per 1.05 gallon kit
We recommend Epoxicote High Build Rapid for jobs that need less down time, Epoxicote High Build Cold Cure for cold environment applications, and Epoxicote High Build Anti-Slip for areas that need added safety from slip hazards.
| Usage Interior/Exterior: | Interior |
| Finish: | Glossy, smooth |
| Suitable for: | Concrete, well bonded paint, wood, some metals |
| Primer Required: | Yes, on bare concrete and very porous surfaces should be primed with 4 Hour Epoxy Primer |
| Recommended Number of Coats: | One is usually sufficient |
| Pot Life: | 25 minutes at 70°F |
| Curing Time (Hours): | At 70°F 12-16 hour for light foot traffic, 24 for normal traffic, 36 to 48 hours for vehicle traffic |
Preparation: Concrete and Brick
Concrete to be treated must be dry, at least four weeks old and free of any soft surface laitance, or contamination All loose material should be removed. Very smooth bare concrete or concrete with soft surface laitance should be etched with Watco Cemtetch and the area thoroughly hosed off and allowed to dry. Grease or oil should be removed with Watco Bio-D (or similar degreaser) and the area thoroughly hosed off and allowed to dry. Very smooth previously painted surface should preferably be abraded to improve adhesion.
Preparation: Steel
Remove loose or flaking material, rust and any previous coatings by wire brushing or disc grinding to achieve a bright surface. Grease or oil should be removed with Watco Bio-D and the metal then washed with water and allowed to dry. Coating should be carried out immediately providing flash rusting has not occurred.
Mixing
Each Epoxicote High Build kit consists of a container of curing agent and a container of resin. The curing agent and resin must be thoroughly mixed together with a paint mixer attached to an electric drill for 2 to 3 minutes until an even color is obtained. Do not mix more than one unit at a time.
Application
Epoxicote High Build: Best results are obtained in warm conditions (minimum 60°F). On horizontal surfaces apply by medium pile type roller (not foam) in one coat.
