Product Detail
Flowpatch® Deep Fill is an easy to mix, pourable material for fast repairs to level concrete surfaces both inside and outside. This Deep Fill formula is perfect for repairing or levelling deeper holes between 1cm-8in in concrete flooring. It is fiber reinforced for extra strength and hardens quickly - it will accept heavy traffic including forklifts only 2 hours after application.
Features and Benefits of Flowpatch® Deep Fill:
- Quick setting, pourable flooring patch that repairs holes, gouges, spalling, crevices or pitted concrete
- Can be applied to deeper holes between 1cm-8in
- Able to part mix: 6 parts powder to 1 part water by volume
- Apply to dry or damp (not wet) surfaces
- Silver Gray, slip resistant finish
- Sets at temperatures as low as 41°F
- Ready for foot traffic after 30 min. & forklift traffic after 2 hours
- Covers approximately 2.5 sq. ft. per 55 lb. kit at 2" thick
- For use on interior and exterior surfaces
- Fiber reinforced
- Includes mixing cup for partial mixing
Specifications
| Usage Interior/Exterior: | Interior or Exterior |
| Primer Required: | No |
| Suitable for: | Concrete |
| Coverage: | 2.5 sq. ft per 55 lb. kit at 2" thick |
| Pot Life: | 5-10 Minutes in 70°F |
| Curing Time (Hours): | 1 Hour in 60°F |
How to Apply
Surface Preparation
The substrate should be clean and free from oil or contaminants. Loose debris should be removed and the surface wire brushed. Flowpatch can be applied to damp (not wet) concrete.
Mixing
Do not mix more than you can use within 10 minutes. Mixing Ratio is 6 parts Flowpatch powder to 1 part water by volume. Gradually add the Flowpatch powder/aggregate to water mixing continuously with a mixing blade on a drill to achieve pourable slurry. Thoroughly mix the sides and base of the powder in the bucket to break up any lumps of unmixed dry powder. Once mixed, curing begins very quickly, so the mixture should be applied immediately. Once thoroughly mixed, do not re-stir as this could potentially weaken the final repair. The remaining powder/aggregate can be stored for future use. Pot Life is 5 to 10 minutes at 70°F.
Application
When a smooth consistency has been produced, simply pour Flowpatch® into the damaged area. After proper mixing, the repair will self-level and need minimal trowelling. Flowpatch resists oils and grease.
Data Sheet
Flowpatch® Deep Fill is an easy to mix, pourable material for fast repairs to level concrete surfaces both inside and outside. This Deep Fill formula is perfect for repairing or levelling deeper holes between 1cm-8in in concrete flooring. It is fiber reinforced for extra strength and hardens quickly - it will accept heavy traffic including forklifts only 2 hours after application.
Features and Benefits of Flowpatch® Deep Fill:
- Quick setting, pourable flooring patch that repairs holes, gouges, spalling, crevices or pitted concrete
- Can be applied to deeper holes between 1cm-8in
- Able to part mix: 6 parts powder to 1 part water by volume
- Apply to dry or damp (not wet) surfaces
- Silver Gray, slip resistant finish
- Sets at temperatures as low as 41°F
- Ready for foot traffic after 30 min. & forklift traffic after 2 hours
- Covers approximately 2.5 sq. ft. per 55 lb. kit at 2" thick
- For use on interior and exterior surfaces
- Fiber reinforced
- Includes mixing cup for partial mixing
| Usage Interior/Exterior: | Interior or Exterior |
| Primer Required: | No |
| Suitable for: | Concrete |
| Coverage: | 2.5 sq. ft per 55 lb. kit at 2" thick |
| Pot Life: | 5-10 Minutes in 70°F |
| Curing Time (Hours): | 1 Hour in 60°F |
Surface Preparation
The substrate should be clean and free from oil or contaminants. Loose debris should be removed and the surface wire brushed. Flowpatch can be applied to damp (not wet) concrete.
Mixing
Do not mix more than you can use within 10 minutes. Mixing Ratio is 6 parts Flowpatch powder to 1 part water by volume. Gradually add the Flowpatch powder/aggregate to water mixing continuously with a mixing blade on a drill to achieve pourable slurry. Thoroughly mix the sides and base of the powder in the bucket to break up any lumps of unmixed dry powder. Once mixed, curing begins very quickly, so the mixture should be applied immediately. Once thoroughly mixed, do not re-stir as this could potentially weaken the final repair. The remaining powder/aggregate can be stored for future use. Pot Life is 5 to 10 minutes at 70°F.
Application
When a smooth consistency has been produced, simply pour Flowpatch® into the damaged area. After proper mixing, the repair will self-level and need minimal trowelling. Flowpatch resists oils and grease.
