Product Detail
Heavy Duty Crack Filler is used for repairing cracks, holes, and other types of damage to concrete or as a high strength adhesive for projects that require a non-sag epoxy with a fast curing time. It is a high modulus, moisture insensitive, non-sag epoxy system. Cartridge packaging allows successful injection into cracks and holes in vertical applications. It can also be used on wet surfaces and even in complete water immersion.
Features and Benefits of Heavy Duty Crack Filler:
- Non-sagging, high-strength two-component 100% solids epoxy
- Easy to use system in a pre-mixed cartridge
- Moisture-resistant
- Good for interiors, exteriors & even water-submerged surfaces
- Bonds concrete, brick, metal, wood and stone
- Full cure in less than 2 hours
- Convenient 9 oz. tube with 2 Static Mixers included
- Covers 20 linear feet at a 1/4" x 1/4" bead
- Use with our Heavy Duty Caulk Gun
Specifications
| Usage Interior/Exterior: | Interior or Exterior |
| Suitable for: | Concrete, brick, wood, stone, block & metal |
| Primer Required: | No |
| Coverage: | 20 linear feet at a 1/4 x 1/4" bead |
| Pot Life: | 5 to 6 min. in static mixer |
| Curing Time (Hours): | Gels in 8 min, tack free in 12 min, full cure in 2 hours at 75°F |
How to Apply
Surface Preparation
New concrete must cure 28 days at 70°F before repairs are made. Remove all dirt, grease, oil, salt or other contaminants by washing surface with Bio-D®, commercial detergent or other suitable cleaner. Rinse thoroughly with fresh, clean water. Remove all loose, unsound, or deteriorated concrete. Smooth concrete surfaces should be sanded or wire brushed to provide a surface profile. For best results, cracks should be chased by grinder using a tuck point blade.
Mixing
The material is properly proportioned when dispensed from the cartridge. Before attaching the static mixing nozzle to the cartridge, dispense a small amount of material into a disposable container until both materials flow evenly from the cartridge. Attach the mixing nozzle to the cartridge and dispense material until a consistent, uniform color with no streaks is obtained. The static mixing nozzle will completely and properly combine the two components and deliver fully mixed ready-to-apply material. For small applications, where the entire cartridge of material will not be used, a portion of material can be dispensed directly from the cartridge without the nozzle onto a flat surface and mixed together by thorough hand mixing. Do not thin with any type of solvent. Save the plastic cap and plug to reseal the unused material in the cartridge.
Application
Apply only when air and surface temperatures are between 35-110°F. It is strongly recommended the material temperature be at least 50°F prior to use. Colder material will require more effort to disperse from the cartridge. Place the mixed material directly in the area to be repaired, then work the material smooth using a hand held steel trowel. Wet the blade of the trowel with Xylene to help ease the final finishing of the material. For larger repair areas, the end of the static mixing nozzle can be cut off to increase the nozzle opening to achieve maximum flow. When using as an adhesive for anchor bolts, fill the hole to half of the depth, then insert the anchor bolt. See Technical Data Sheet. When using more than one cartridge, the nozzle can be transferred from the empty cartridge to the new one in order to minimize material loss. Before transferring the nozzle, be sure to first dispense a small amount of material from the new cartridge to ensure both components have an even flow, then immediately attach the nozzle. Working time once dispensed is 8 minutes at 75°F. Do not allow material to stand in static mixing nozzle for longer than 5-6 minutes.
NOTE: Due to the two component configuration of the cartridge the plunger will only travel ½ the length of the cartridge when empty.
Clean-Up
Use Xylene.
Data Sheet
Heavy Duty Crack Filler is used for repairing cracks, holes, and other types of damage to concrete or as a high strength adhesive for projects that require a non-sag epoxy with a fast curing time. It is a high modulus, moisture insensitive, non-sag epoxy system. Cartridge packaging allows successful injection into cracks and holes in vertical applications. It can also be used on wet surfaces and even in complete water immersion.
Features and Benefits of Heavy Duty Crack Filler:
- Non-sagging, high-strength two-component 100% solids epoxy
- Easy to use system in a pre-mixed cartridge
- Moisture-resistant
- Good for interiors, exteriors & even water-submerged surfaces
- Bonds concrete, brick, metal, wood and stone
- Full cure in less than 2 hours
- Convenient 9 oz. tube with 2 Static Mixers included
- Covers 20 linear feet at a 1/4" x 1/4" bead
- Use with our Heavy Duty Caulk Gun
| Usage Interior/Exterior: | Interior or Exterior |
| Suitable for: | Concrete, brick, wood, stone, block & metal |
| Primer Required: | No |
| Coverage: | 20 linear feet at a 1/4 x 1/4" bead |
| Pot Life: | 5 to 6 min. in static mixer |
| Curing Time (Hours): | Gels in 8 min, tack free in 12 min, full cure in 2 hours at 75°F |
Surface Preparation
New concrete must cure 28 days at 70°F before repairs are made. Remove all dirt, grease, oil, salt or other contaminants by washing surface with Bio-D®, commercial detergent or other suitable cleaner. Rinse thoroughly with fresh, clean water. Remove all loose, unsound, or deteriorated concrete. Smooth concrete surfaces should be sanded or wire brushed to provide a surface profile. For best results, cracks should be chased by grinder using a tuck point blade.
Mixing
The material is properly proportioned when dispensed from the cartridge. Before attaching the static mixing nozzle to the cartridge, dispense a small amount of material into a disposable container until both materials flow evenly from the cartridge. Attach the mixing nozzle to the cartridge and dispense material until a consistent, uniform color with no streaks is obtained. The static mixing nozzle will completely and properly combine the two components and deliver fully mixed ready-to-apply material. For small applications, where the entire cartridge of material will not be used, a portion of material can be dispensed directly from the cartridge without the nozzle onto a flat surface and mixed together by thorough hand mixing. Do not thin with any type of solvent. Save the plastic cap and plug to reseal the unused material in the cartridge.
Application
Apply only when air and surface temperatures are between 35-110°F. It is strongly recommended the material temperature be at least 50°F prior to use. Colder material will require more effort to disperse from the cartridge. Place the mixed material directly in the area to be repaired, then work the material smooth using a hand held steel trowel. Wet the blade of the trowel with Xylene to help ease the final finishing of the material. For larger repair areas, the end of the static mixing nozzle can be cut off to increase the nozzle opening to achieve maximum flow. When using as an adhesive for anchor bolts, fill the hole to half of the depth, then insert the anchor bolt. See Technical Data Sheet. When using more than one cartridge, the nozzle can be transferred from the empty cartridge to the new one in order to minimize material loss. Before transferring the nozzle, be sure to first dispense a small amount of material from the new cartridge to ensure both components have an even flow, then immediately attach the nozzle. Working time once dispensed is 8 minutes at 75°F. Do not allow material to stand in static mixing nozzle for longer than 5-6 minutes.
NOTE: Due to the two component configuration of the cartridge the plunger will only travel ½ the length of the cartridge when empty.
Clean-Up
Use Xylene.
