Product Detail
Non-slip step treads are an easy and highly effective way to improve safety to stairs around your facility. These easy-to-apply tough stair treads have a surface of resin-bonded aluminum oxide for a long lasting gritty finish. Anti-slip step treads are suitable for concrete, wood, brick, stone and metal stairs and can be used in interior and exterior applications for medium traffic areas.
Features and Benefits of Slip-Free Stair Treads:
- Extremely tough, resin-bonded aluminum oxide grit for a long lasting finish
- Water resistant, self-adhesive, peel-off backing
- Service temperatures -22°F to 160°F, but must be first applied over 50°F
- For interior or exterior use, medium duty areas
- Can be applied to concrete, wood, brick, stone, & metal
- Size: 6" x 24
- Allow 24 hours for product to fully set before being walked on, if possible
- Use the Safety Tape Primer on dusty concrete, porous, or other weak surfaces to ensure better adhesion
- To protect against wearing and water seepage, use Safety Tape Edge Sealer
Samples available upon request
Specifications
| Usage Interior/Exterior: | Interior or Exterior |
| Suitable for: | Concrete, wood, brick, stone and metal floors and ramps |
| Primer Required: | Use Safety Tape Primer on dusty, porous or gritty surfaces |
How to Apply
Surface Preparation: Apply to clean, smooth, dry surfaces such as painted or varnished wood, concrete, metal, tiles, and terrazzo. Apply direct to smooth, hard concrete; dusty concrete will require a primer.
Priming: Smooth, non porous, dust free surfaces do not require priming. To improve adhesion on weak, dusty surfaces, apply a coat of Safety Tape Primer.
Application: Avoid application at temperatures below 50°F. Low temperatures can reduce adhesion. On steps and nosings, apply the product approximately 10mm in from the edge to prevent premature wear and edge curl. Peel back the backing strip approximately 50mm to reveal the adhesive layer. Avoid removing too much of the backing strip, but slowly keep peeling it back while firming the product into place. Firming down by hand or foot pressure is generally sufficient. Avoid stretching the tapes and treads during application.
Adhesion: Although the product can be walked on virtually straight away, the adhesive can take 24 hours to set fully. Immediately after placing the item onto the substrate, it can be peeled off reasonably easily for repositioning if necessary. Avoid lifting the tread or removing the tape to allow the adhesive to cure. Please allow the adhesive to set for up to 24 hours, especially if using in heavily trafficked or hazardous areas.
Non-slip step treads are an easy and highly effective way to improve safety to stairs around your facility. These easy-to-apply tough stair treads have a surface of resin-bonded aluminum oxide for a long lasting gritty finish. Anti-slip step treads are suitable for concrete, wood, brick, stone and metal stairs and can be used in interior and exterior applications for medium traffic areas.
Features and Benefits of Slip-Free Stair Treads:
- Extremely tough, resin-bonded aluminum oxide grit for a long lasting finish
- Water resistant, self-adhesive, peel-off backing
- Service temperatures -22°F to 160°F, but must be first applied over 50°F
- For interior or exterior use, medium duty areas
- Can be applied to concrete, wood, brick, stone, & metal
- Size: 6" x 24
- Allow 24 hours for product to fully set before being walked on, if possible
- Use the Safety Tape Primer on dusty concrete, porous, or other weak surfaces to ensure better adhesion
- To protect against wearing and water seepage, use Safety Tape Edge Sealer
Samples available upon request
| Usage Interior/Exterior: | Interior or Exterior |
| Suitable for: | Concrete, wood, brick, stone and metal floors and ramps |
| Primer Required: | Use Safety Tape Primer on dusty, porous or gritty surfaces |
Surface Preparation: Apply to clean, smooth, dry surfaces such as painted or varnished wood, concrete, metal, tiles, and terrazzo. Apply direct to smooth, hard concrete; dusty concrete will require a primer.
Priming: Smooth, non porous, dust free surfaces do not require priming. To improve adhesion on weak, dusty surfaces, apply a coat of Safety Tape Primer.
Application: Avoid application at temperatures below 50°F. Low temperatures can reduce adhesion. On steps and nosings, apply the product approximately 10mm in from the edge to prevent premature wear and edge curl. Peel back the backing strip approximately 50mm to reveal the adhesive layer. Avoid removing too much of the backing strip, but slowly keep peeling it back while firming the product into place. Firming down by hand or foot pressure is generally sufficient. Avoid stretching the tapes and treads during application.
Adhesion: Although the product can be walked on virtually straight away, the adhesive can take 24 hours to set fully. Immediately after placing the item onto the substrate, it can be peeled off reasonably easily for repositioning if necessary. Avoid lifting the tread or removing the tape to allow the adhesive to cure. Please allow the adhesive to set for up to 24 hours, especially if using in heavily trafficked or hazardous areas.
