Product Detail
Rust-Oleum High Performance V2100 System Rust Preventive Enamel Spray Paint is ideal for industrial spray painting projects. This tough spray paint provides a professional finish that resists chipping, cracking and peeling. The advanced formula in this aerosol provides the best-possible corrosion protection with easy, one-coat coverage and long-lasting color, gloss and durability.
Features and Benefits of V2100 System Enamel Spray Paint:
- High-output tip covers 50% faster
- Dries to a touch in 20 minutes
- Withstands heat up to 200°F
- Ideal for metal, steel, masonry and wood surfaces
- Can also be used as a touch-up paint
- Meets USDA requirements for incidental food contact; accepted for use in federally registered Canadian food facilities; VOC-compliant nationwide
Specifications
| Usage Interior/Exterior: | Interior or Exterior |
| Suitable for: | Metal, steel, masonry, wood |
| Finish: | Smooth, gloss finish |
| Primer Suggestions: | Not required, but for best performance, use with V2182838 Gray Primer |
| Coverage: | 12-20 sq ft |
| Cure Time: | Tack free in 20mins |
| Recoat Time: | Within 1 hour or after 24 hours depending on temperature |
How to Apply
Surface Preparation
Remove all dirt, grease, oil, salt and chemical contaminants by washing the surface with a commercial detergent, or other suitable cleaning method. Rinse with fresh water and allow to thoroughly dry. Remove loose paint and rust with a wire brush or sandpaper. Previously coated surfaces must be sound and in good condition. Smooth, hard, or glossy finishes should be scarified by sanding to create a surface profile.
WARNING! If you scrape, sand or remove old paint from any surface, you may release lead paint dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE; ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH approved respirator to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.
Surface Preparation - Steel: Hand tool (SSPC-SP-2) or power tool (SSPC-SP-3) clean to remove loose rust, mill scale, and deteriorated previous coatings.
Surface Preparation - Previously Coated: Previously coated surfaces must be sound and in good condition. Smooth, hard, or glossy finishes should be scarified by sanding to create a surface profile.
Application
Use when temperature is above 50°F (10°C) and humidity is below 85% to ensure proper drying. Surface temperature must be between 50-100°F (10-38°C). Use a primer on bare or rusted surfaces.
Protect surrounding surfaces from overspray. Overspray can carry a significant distance. Shake can for one minute after mixing ball is heard. Hold can 10-14 inches from surface. Apply several light coats a few minutes apart to avoid drips and runs.
Dry & Recoat Times
Recoat within 1 hour or after 24 hours. Allow more time in cooler temperatures.
Clean-Up
Wipe off tip before storing. Clean-up wet paint with xylene or mineral spirits. Properly discard empty container. Do not burn or place in trash compactor. Empty container can be recycled.
Clogging
If the valve clogs, twist and pull off spray tip and rinse in a solvent such as mineral spirits. Do not insert any object into can valve opening.
Data Sheet
Rust-Oleum High Performance V2100 System Rust Preventive Enamel Spray Paint is ideal for industrial spray painting projects. This tough spray paint provides a professional finish that resists chipping, cracking and peeling. The advanced formula in this aerosol provides the best-possible corrosion protection with easy, one-coat coverage and long-lasting color, gloss and durability.
Features and Benefits of V2100 System Enamel Spray Paint:
- High-output tip covers 50% faster
- Dries to a touch in 20 minutes
- Withstands heat up to 200°F
- Ideal for metal, steel, masonry and wood surfaces
- Can also be used as a touch-up paint
- Meets USDA requirements for incidental food contact; accepted for use in federally registered Canadian food facilities; VOC-compliant nationwide
| Usage Interior/Exterior: | Interior or Exterior |
| Suitable for: | Metal, steel, masonry, wood |
| Finish: | Smooth, gloss finish |
| Primer Suggestions: | Not required, but for best performance, use with V2182838 Gray Primer |
| Coverage: | 12-20 sq ft |
| Cure Time: | Tack free in 20mins |
| Recoat Time: | Within 1 hour or after 24 hours depending on temperature |
Surface Preparation
Remove all dirt, grease, oil, salt and chemical contaminants by washing the surface with a commercial detergent, or other suitable cleaning method. Rinse with fresh water and allow to thoroughly dry. Remove loose paint and rust with a wire brush or sandpaper. Previously coated surfaces must be sound and in good condition. Smooth, hard, or glossy finishes should be scarified by sanding to create a surface profile.
WARNING! If you scrape, sand or remove old paint from any surface, you may release lead paint dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE; ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH approved respirator to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.
Surface Preparation - Steel: Hand tool (SSPC-SP-2) or power tool (SSPC-SP-3) clean to remove loose rust, mill scale, and deteriorated previous coatings.
Surface Preparation - Previously Coated: Previously coated surfaces must be sound and in good condition. Smooth, hard, or glossy finishes should be scarified by sanding to create a surface profile.
Application
Use when temperature is above 50°F (10°C) and humidity is below 85% to ensure proper drying. Surface temperature must be between 50-100°F (10-38°C). Use a primer on bare or rusted surfaces.
Protect surrounding surfaces from overspray. Overspray can carry a significant distance. Shake can for one minute after mixing ball is heard. Hold can 10-14 inches from surface. Apply several light coats a few minutes apart to avoid drips and runs.
Dry & Recoat Times
Recoat within 1 hour or after 24 hours. Allow more time in cooler temperatures.
Clean-Up
Wipe off tip before storing. Clean-up wet paint with xylene or mineral spirits. Properly discard empty container. Do not burn or place in trash compactor. Empty container can be recycled.
Clogging
If the valve clogs, twist and pull off spray tip and rinse in a solvent such as mineral spirits. Do not insert any object into can valve opening.
