Product Detail
Decorative Vinyl Chips can be used to give your floor a personalized finish. Commonly used in garages, commercial & institutional facilities like schools, cafeterias, showrooms, locker rooms and more.
Features and Benefits of Decorative Vinyl Epoxy Floor Chips:
- Sold in 1 lb. packs
- For use with most of our epoxy coatings
- Simply spread chips by hand, then back roll while coating is still wet
- Available in 4 different color assortments
- A sparse or a full broadcast of the chips can be used
- To achieve a Full Broadcast use 18-20 pounds per 100 sq. ft.
- To achieve a Sparse Broadcast use 1/4 - 1/2 pounds per 100 sq. ft.
Apply one or two finish coats of Clear Coat Epoxy Floor Coating or Clear Coat Plus Epoxy Floor Coating to lock in the Vinyl Chips and obtain a smooth, easy to clean finish.
Specifications
| Properties: | Must be overcoated with a clear top coat |
| Usage Interior/Exterior: | Interior |
| Coverage: | Sparse coverage: (1)-1 lb. bag per 100 sq. ft |
How to Apply
Application
Apply the selected base coat in accordance to all published surface preparation and application procedures for that coating system. Refer to the Technical Data Sheet of the selected system for complete information.
Do Not mix Vinyl Chips into the coating, they are to be broadcast onto the wet coating after it has been applied. Work in sections. Keep the size of the working section appropriate to facilitate an even distribution of the Vinyl Chips.
Immediately after completing the final roller passes, begin broadcasting the Vinyl Chips onto the wet coating. Distribute the Vinyl chips by tossing them up into the air above the coating in an underhand manner. This allows the chips to drop directly down onto the surface of the coating. Avoid slinging the chips onto the coating with a side arm throw.
Full Broadcast
Distribute 18-20 pounds of Vinyl Chips per every 100 square feet of surface area. The entire surface of the coated floor should be completely covered with Vinyl chips. After curing overnight, sweep off all loose chips, then scrape the surface with an upright floor scraper. Re-sweep or vacuum the surface. Then topcoat.
Sparse Broadcast
Distribute 1/4 - 1/2 pounds of Vinyl Chips per every 100 square feet of surface area in a uniform manner. A higher amount of Vinyl Chips can be used if desired. Allow to cure overnight, then topcoat.
Apply one or two finish coats of Clear Coat or Clear Coat Plus to lock in the Vinyl chips and obtain a smooth, easy to clean finish.
Data Sheet
Decorative Vinyl Chips can be used to give your floor a personalized finish. Commonly used in garages, commercial & institutional facilities like schools, cafeterias, showrooms, locker rooms and more.
Features and Benefits of Decorative Vinyl Epoxy Floor Chips:
- Sold in 1 lb. packs
- For use with most of our epoxy coatings
- Simply spread chips by hand, then back roll while coating is still wet
- Available in 4 different color assortments
- A sparse or a full broadcast of the chips can be used
- To achieve a Full Broadcast use 18-20 pounds per 100 sq. ft.
- To achieve a Sparse Broadcast use 1/4 - 1/2 pounds per 100 sq. ft.
Apply one or two finish coats of Clear Coat Epoxy Floor Coating or Clear Coat Plus Epoxy Floor Coating to lock in the Vinyl Chips and obtain a smooth, easy to clean finish.
| Properties: | Must be overcoated with a clear top coat |
| Usage Interior/Exterior: | Interior |
| Coverage: | Sparse coverage: (1)-1 lb. bag per 100 sq. ft |
Application
Apply the selected base coat in accordance to all published surface preparation and application procedures for that coating system. Refer to the Technical Data Sheet of the selected system for complete information.
Do Not mix Vinyl Chips into the coating, they are to be broadcast onto the wet coating after it has been applied. Work in sections. Keep the size of the working section appropriate to facilitate an even distribution of the Vinyl Chips.
Immediately after completing the final roller passes, begin broadcasting the Vinyl Chips onto the wet coating. Distribute the Vinyl chips by tossing them up into the air above the coating in an underhand manner. This allows the chips to drop directly down onto the surface of the coating. Avoid slinging the chips onto the coating with a side arm throw.
Full Broadcast
Distribute 18-20 pounds of Vinyl Chips per every 100 square feet of surface area. The entire surface of the coated floor should be completely covered with Vinyl chips. After curing overnight, sweep off all loose chips, then scrape the surface with an upright floor scraper. Re-sweep or vacuum the surface. Then topcoat.
Sparse Broadcast
Distribute 1/4 - 1/2 pounds of Vinyl Chips per every 100 square feet of surface area in a uniform manner. A higher amount of Vinyl Chips can be used if desired. Allow to cure overnight, then topcoat.
Apply one or two finish coats of Clear Coat or Clear Coat Plus to lock in the Vinyl chips and obtain a smooth, easy to clean finish.
